Shimpo DT-205L User Manual download pdf (Page 3)

INSTRUMENTSINSTRUMENTS

INSTRUMENTS

1701 Glenlake Avenue Itasca, IL 60143 · phone: (800) 237-7079 · fax: (630) 924-0342 · www.shimpoinst.com

MEMORY RECALLMEMORY RECALL

MEMORY RECALL

The following readings are stored in memory for 5 minutes

after release of the power switch:

• Last reading

• Minimum reading

• Maximum reading

These readings can be recalled by pressing the memory switch.

During measurements, ten extra readings can also be captured,

stored, then recalled using the memory switch. While the

tachometer is in use, simply press the memory

switch each time a reading needs to be stored.

Contact Mode (Rate Functions)

When the rate functions are selected (mPM, YPM, FPM and

IPM), the memory store and recall functions are accomplished

exactly as noted above.

Contact Mode (Length Functions)

When the counting functions are selected, the memory store

and recall functions are accomplished in the same manner as

the non-contact mode, the only exception being the maximum

and minimum readings (they do not exist).

To clear the memory completely (for all functions), press the

memory switch for approximately 6 seconds until the display

shows CCCCC, then release the switch.

RANGE AND ACCURACYRANGE AND ACCURACY

RANGE AND ACCURACY

Place selector switch in the proper position. Using the 200L

adapter and 6" master wheel, the following industrial units

of measurement are achieved:

BABA

TERY REPLACEMENTTERY REPLACEMENT

TERY REPLACEMENT

Low battery voltage is indicated by flashing LOW BAT on the

display. Remove end cover by using a coin or appropriate

screwdriver and replace both batteries. Please ensure proper

polarity.

Although the tachometer alone is able to achieve

the above ranges, the 6" master wheel has

maximum speed limitation of 5,000 FPM (for safety

reasons)

MODEL DT-205L

R: REVOLUTIONS SINGLE RANGE ACCURACY RESOLUTION

Non-Contact RPM 6 - 8,300 ± 1

(rev./min.)

8,300 - 25,000 ± 2 1

25,000 - 99,999 ±0.006% of reading ±1digit

(or ±6 RPM max.)

Contact RPM (rev./min.) 0.8 - 9,999.9 ±0.6% 0.1

10,000 - 25,000 ±0.006% of reading ±1digit 1

(or ±2 RPM max.)

F: FEET SINGLE RANGE ACCURACY RESOLUTION

F/M (feet/min.) 0.4 - 9,999.9 ± 0.6 0.1

10,000 - 12,500 ± 1 1

FT (feet) 0.10 - 999.99 0.01

1,000.0 - 9,999.9 0.1

10,000 - 99,999 1

Y: YARDS SINGLE RANGE ACCURACY RESOLUTION

Y/M (yards/min.) 0.13 - 999.99 ± 0.06 0.01

1,000.0 - 4,167.0 ± 0.3 0.1

YRd (length) 0.02 - 999.99 0.01

1,000.0 - 9,999.9 0.1

10,000 - 99,999 1

I: INCHES SINGLE RANGE ACCURACY RESOLUTION

I/M (inches/min.) 5 - 99,999 ±0.006% of reading ±1digit

(or ±6 RPM max.)

IN (length) 1.0 - 99,999 0.1

10,000 - 99,999 1

m: METERS SINGLE RANGE ACCURACY RESOLUTION

m/M (meters/min.) 0.11 - 999.99 ± 0.06 0.01

1,000.0 - 3,810.0 ± 0.3 0.1

m (length) 0.02 - 999.99 0.01

1,000.0 - 9,999.9 0.1

10,000 - 99,999 1

NOTE: When using the 6" master wheel, accuracy can be

affected as much as 0.3% of reading

1 2 3 4

Comments to this Manuals

No comments

Shimpo DT-205L User Manual Page 3

Comments to this Manuals

Related products and manuals for Tools Shimpo DT-205L